Shure Beta 87C

Vocal Microphone

The Shure Beta 87C vocal microphone is precision-engineered to deliver an extremely smooth, extended high-end frequency response in a cardioid condenser design. The warm, natural sound creates an ideal environment for personal monitoring with excellent rear rejection.

An advanced, cartridge shock mount system, hardened steel-mesh grille, and superior build quality withstand the rigors of daily touring and sound reinforcement.

Features

• Premier live performance microphone with Shure quality, ruggedness, and reliability
• Uniform cardioid pick-up pattern for maximum gain before feedback and excellent rejection of off-axis sound
• Smooth, wide frequency response with slight presence rise and controlled proximity effect tailored for vocals
• Advanced cartridge shock mount system absorbs mechanical shock and minimizes handling noise
• Very low susceptibility to RF and electromagnetic hum
• Dent-resistant steel mesh grille and enamel coated metal alloy construction resist wear and abuse
• Effective built-in pop filter reduces undesirable wind and breath noise

Applications

General Rules for Use

• Do not cover any part of the microphone grille with your hand, as this will adversely affect microphone performance.
• Aim the microphone toward the desired sound source (such as the talker, singer, or instrument) and away from unwanted sources.
• Place the microphone as close as practical to the desired sound source.
• Work close to the microphone for extra bass response.
• Use only one microphone to pick up a single sound source.
• For better gain before feedback, use fewer microphones.
• Keep the distance between microphones at least three times the distance from each microphone to its source (“three to one rule”).
• Place microphones as far as possible from reflective surfaces.
• Add a windscreen when using the microphone outdoors.
• Avoid excessive handling to minimize pickup of mechanical noise and vibration.

Applications And Placement

The following table lists the most common applications and placement techniques. Keep in mind that microphone technique is largely a matter of personal taste; there is no one “correct” microphone position.

Avoiding Pickup of Unwanted Sound Sources

Place the microphone so that unwanted sound sources, such as monitors and loudspeakers, are directly behind it. To minimize feedback and ensure optimum rejection of unwanted sound, always test microphone placement before a performance.

Recommended Loudspeaker Locations for Cardioid Microphones

Proximity Effect

Unidirectional (cardioid) microphones progressively boost bass frequencies by 6 to 10 dB below 100 Hz when the microphone is at a distance of about 6 mm (1/4 in.) from the sound source. This phenomenon, known as proximity effect, can be used to create a warmer, more powerful sound. To prevent explosive low frequency sound during close-up use, the bass response gradually rolls off. This provides greater control and helps the user take advantage of proximity effect.

Power Requirements

This microphone requires phantom power and performs best with a 48 Vdc supply (IEC-61938). However, it will operate with slightly decreased headroom and sensitivity with supplies as low as 11 Vdc.

Most modern mixers provide phantom power. You must use a balanced microphone cable: XLR-to-XLR or XLR-to-TRS.

Specifications

Type

Electret Condenser

Frequency Response

50 to 16,000 Hz

Polar Pattern

Cardioid

Output Impedance

EIA rated at150  Ω(100  Ωactual)

Sensitivity

at 1kHz,open circuit voltage: -51  dBV/Pa(2  mV)[1]

Maximum SPL

1 kHz at 1% THD,1 kΩ load: 139  dB

Signal-to-Noise Ratio

70.5 dB[2]

Dynamic Range

at 1kHz,1 kΩ load: 117 dB

Clipping Level

1 kHz at 0.25% THD,1 kΩ load: -6 dBV(0.5 V)

Self Noise

typical,equivalent SPL, A-weighted: 22  dB

Hum Pickup

typical, at 60 Hz, equivalent SPL/mOe: -5 dB

Polarity

Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3

Weight

Net: 0.207 kg (0.475 lbs)

Connector

Three-pin professional audio (XLR), male, balanced

Housing

Aluminum construction with painted blue metallic finish, and hardened steel grille with nickel satin chrome plating

Power Requirements

11 to 52 V DC phantom power(1.2 mA)

[1] 1 Pa=94 dB SPL

[2] S/N ratio is difference between 94 dB SPL and equivalent SPL of self noise, A-weighted

Overall Dimensions

Typical Frequency Response

Typical Polar Pattern

BLOCK DIAGRAM

Accessories

Furnished Accessories

Optional Accessories

Replacement Parts

Certifications

This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.

The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance

Authorized European representative:

Shure Europe GmbH

Headquarters Europe, Middle East & Africa

Department: EMEA Approval

Jakob-Dieffenbacher-Str. 12

75031 Eppingen, Germany

Phone: 49-7262-92 49 0

Fax: 49-7262-92 49 11 4

Email: info@shure.de