WAVENET Mobile radio-link transmitter BS-5000
The Wavenet BS-5000 base transmitter is a long range broadcast quality audio radio link, designed for an easy handling and high reliability.
BS-5000 transmitter has a RF power above 30W with up to 200 selectable working frequencies (174 to 500 MHz- 40MHz window). This device has been made using the highest current manufacturing standards. It has SW controlled protection redundancy developed by Wavenet.
Wavenet BS-5000 also has 5 inputs with switchable micro-line gain selector. This versatility allows you to virtually manage with any situation.
It has a complete backligthed display with navigation keys acting and posing all parameters, alarms and equipment selections.
This system can be easily transported by mean of a handle buit-in in one of its sides.
Accepts 90-250VAC and 9-36VDC powering, allowing its use in any situation.
It may be optionally remotely controlled by Ethernet.
Technical characteristics
| Frequency generation | By mean of a PLL controlled digital synthesizer with 4 buttons for direct selection of four requencies. |
| Transmission frequency | 174 to 500 MHz programmable (window of 40 MHz depending on versions). |
| Channels | Up to 200 programmable. |
| Modulation | FM +/- 20 kHz (other ones under request). |
| Power | 30W over 50 Ohm. |
| RF output connector | N female on the rear panel. |
| RF output impedance | 50 Ohms. |
| DSP | 16 bit digital signal processor for managing and controlling the system, including 16 A/D and 16 D/A converters. |
| Frequency stability | Better than +/- 1 ppm from -10C to +50C. |
| AF bandwidth | 5 / 7.5 / 10 y 12.5 kHz configurable. |
| Distortion | Better tahn 0.3% |
| Audio input connectors | 5 XLR3 female and mic /líne selector. |
| Input impedance | 600 Ohms and 10 kOhms balanced. Mixing controls for each one and PFL (pre-monitoring). |
| Monitoring | 6.35 mm stereo connector with volume control and > 200mW output. |
| Input audio level | Micro: between -68 and -35 dBm. Line: between 0 and +12 dBm. |
| Spurious | Better than 65 dBc. |
| NR system | ON/OFF selectable“Silenzo+” compressor-limiter. |
| SNR | >65dB at 75 us pre-emphasis and 20 kHz modulation. |
| Residual asynchronous AM modulation | Better than -60 dBc. |
| Residual synchrounous AM modulation | Better than -50 dBc. |
| Pre-emphasis | 50us / 75us / No pre-emphasis. |
| Mechanized aluminum case. | |
| Dimensions | 355x85x295 mm with rack 19” 2U adaptor and handle transport. |
| Powering | Continuous 90 to 250 VAC - IEC connector Continuous 9 to 36VDC - 15 pins Sub-D male connector. |
| Consumption | Below 200 W. |
| Thermal range | -10 C to +50 C. |
| Weight | 4.2 kg |
| Ventilation | 2 fans for forced convection. |
| Protections | ROE, thermal, VDC reverse polarity. |
| ON/OFF switch. | |
| 9 pins Sub-D connector for serial programming in the rear pannel. | |
| Display | |
|---|---|
| This equipment has a 4 lines x 20 characteers display with four buttons for menu navigation. It shows, among others, indications and adjustment of: | |
| - Working frequency. | |
| - Direct access to 4 preset frequencies. | |
| - Transmitted power. | |
| - Reflected power. | |
| - Modulation levels. | |
| - Pre-emphasis. | |
| - Compressor-limiter. | |
| - Thermal and ROE alarms. | |
| - Power source indication. | |
| - Screen contrast. | |
| - Screen back light. | |
| - Power ON LED indication. | |
| - PLL engage/disengage LED indication. | |
| - ROE alarm LED indication. | |
| - Thermal alarm LED indication. | |
